View AD704JNZ_5025112.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

picoampere input current quad bipolar op amp ad704 rev. e information furnished by analog devices is believed to be accurate and reliable. however, no responsibility is assumed by analog devices for its use, nor for any infringements of patents or other rig hts of third parties that may result from its use. specifications subject to change without notice. no license is granted by implication or otherwise under any patent or patent rights of analog devices. trademarks and registered trademarks are the property of their respective owners. one technology way, p.o. box 9106, norwood, ma 02062 - 9106, u.s.a. tel: 781.329.4700 www.analog.com fax: 781.461.3113 ? 2001- 2010 analog de vices, inc. all rights reserved. features high dc p recision 150 v m ax imum o ffset v oltage 1 .5 v/ c max imum o ffset voltage d rift 27 0 pa m ax imum i nput b ias c urrent 0.3 pa/ c t ypical i b d rift low n oise : 0.5 v p - p typical n oise : 0.1 hz to 10 hz low p ower : 600 a max imum s upply current per a mplifier dual v ersion: ad706 applications industrial/process c ontrols weigh s cales ecg/ekg i nstrumentation low f requency active f ilters general description the ad704 is a quad, low power bipolar op amp that has the low input bias current of a bifet amplifier and offers a signifi - cantly lower i b drift over temperature. it u s es super beta bipolar input transistors to achieve picoampere input bias current levels (similar to fet input amplifiers at room temperature), while its i b typically increases only by 5 at 125c (unlike a bifet amp, for which i b doubles every 10c , resulting in a 1000 increase at 125c). in addition , the ad704 achieves 150 v offset voltage and the low noise characteristics of a precision bipolar input op amp. because it has only 1/20 the input bias current of an op07, the ad704 does not require the commonly used balancing resistor. furthermore, the current noise is 1/ 5 tha t of the op07 , which makes the ad704 usable with much higher source impedances. at 1/6 the supply cu rrent (per amplifier) of the op07, the ad704 is better suited for todays higher density circuit boards and battery - powered applications. the ad704 is an ex cellent choice for use in low frequency active filters in 12 - and 14 - bit data acquisition systems, in precision instrumentation, and as a high quality integrator. the ad704 is internally compensated for unity gain stability. the ad704j is rated over the co mmercial temperature range of 0c to 70c. the ad704a is rated over the industrial temperature of ? 40c to +85c. the ad704s is rated over the military tem p erature range of ? 55c to +125c , processed to mil - std - 883b. c onnection d iagrams output 1 ?in 2 +in 3 +v s 4 output 14 ?in 13 +in 12 ?v s 11 +in 5 ?in 6 output 7 +in 10 ?in 9 output 8 1 4 2 3 ad704 top view (not to scale) 00818-001 output 1 ?in 2 +in 3 +v s 4 output 16 ?in 15 +in 14 ?v s 13 +in 5 ?in 6 output 7 8 +in 12 ?in 11 output nc nc 10 9 1 4 2 3 ad704 top view (not to scale) nc = no connect 00818-002 figure 1 . 14 - lead plastic dip (n) figure 2 . 16 - lead soic (r) package 4 +in1 5 nc 6 +v s 7 nc 8 +in2 nc = no connect 18 +in4 17 nc 16 ?v s 15 nc 14 +in3 13 ?in3 12 out3 11 nc 10 out2 9 19 20 1 2 3 ?in2 ?in4 out4 nc out1 ?in1 1 4 2 3 ad704 top view (not to scale) 00818-003 figure 3 . 20 - terminal lcc (e - 20- 1 ) package 100 10 1 0.1 0.01 ?55 25 125 temperature (c) typical i b (na) typical jfet amp ad704 00818-004 figure 4 . input bias current over temperature table 1. low i b @ 125c model 30v 16v 1.3 to 5v next generation single n/a ad8663 ad8603 n/a dual ad706 ad8667 ad8607 ad8622 quad ad704 ad8669 ad8609 ad8624
ad704 rev. e | page 2 of 16 table of contents features .............................................................................................. 1 applications ....................................................................................... 1 general description ......................................................................... 1 connection diagrams ...................................................................... 1 revision history ............................................................................... 2 specifications ..................................................................................... 3 absolute maximum ratings ............................................................5 esd caution ...................................................................................5 typical performance characteristics ..............................................6 theory of operation ...................................................................... 11 outline dimensions ....................................................................... 13 ordering guide .......................................................................... 14 revision history 1/10 r ev. d to r ev. e updated format .................................................................. universal changes to features and g eneral description section, added table 1, renumbered sequentially .................................... 1 changes to table 2 ............................................................................ 3 changes to table 3 ............................................................................ 5 updated outline dimensions ....................................................... 13 changes to ordering guide .......................................................... 14 12 /09 rev. c to rev. d updated outline dimensions ....................................................... 10 changes to ordering guide .......................................................... 10 11 /01 r ev . b to r ev . c edits to features ................................................................................ 1 edits to product description .......................................................... 1 edits to a bsolute m aximum r atings ............................................. 3 deleted m etalization p hotograph .................................................. 3 edits to o rdering g uide .................................................................. 4
ad704 rev. e | page 3 of 16 specifications t a = 25 c, v cm = 0 v, and v s = 1 5 v dc, unless otherwise noted. table 2. ad704j/a parameters conditions min typ max unit input offset voltage initial offset 50 150 v offset t min ? t max 100 250 v vs. temp, average tc 0.2 1.5 v/c vs. supply (psrr) v s = 2 v to 18 v 100 132 db t min ? t max v s = 2.5 v to 18 v 100 126 db long - term stability 0.3 v/month input bias current 1 v cm = 0 v 100 270 pa v cm = 13.5 v 300 pa vs. temp, average tc 0.3 pa/c t min ? t max v cm = 0 v 300 pa v cm = 13.5 v 400 pa input offset current v cm = 0 v 80 250 pa v cm = 13.5 v 300 pa vs. temp, average tc 0.6 pa/c t min ? t max v cm = 0 v 100 300 pa v cm = 13.5 v 100 400 pa matching characteristics offset voltage 250 v t min ? t max 400 v input bias current 2 500 pa t min ? t max 600 pa common - mode rejection 3 94 db t min ? t max 94 db power supply rejection 4 94 db t min ? t max 94 db crosstalk 5 f = 10 hz r load = 2 k ? 150 db frequency response unity gain crossover frequency 0.8 mhz slew rate, unity gain g = ?1 0.15 v/ s slew rate t min ? t max 0.1 v/ s input impedance differential 40||2 m ? ||pf common - mode 300||2 g ? ||pf input voltage range common - mode voltage 13.5 14 v common - mode rejection ratio v cm = 13.5 v 100 132 db t min ? t max 98 128 db input current noise 0.1 hz to 10 hz 3 pa p -p f = 10 hz 50 fa/ hz input voltage noise 0.1 hz to 10 hz 0.5 v p -p f = 10 hz 17 nv/ hz f = 1 khz 15 22 nv/ hz
ad704 rev. e | page 4 of 16 ad704j/a parameters conditions min typ max unit open - loop gain v o = 12 v r load = 10 k ? 200 2000 v/mv t min ? t max 150 1500 v/mv v o = 10 v r load = 2 k ? 200 1000 v/mv t min ? t max 150 1000 v/mv output c haracteristics voltage swing r load = 10 k ? v t min ? t max 13 14 current short c ircuit 15 ma capacitive load drive capability gain = 1 10,000 pf power supply rated performance 15 v operating range 2.0 18 v quiescent current 1.5 2.4 ma t min ? t max 1.6 2.6 ma transistor count number of t ransistors 180 1 bias current specifications are guaranteed maximum at either input. 2 input bias current match is the maximum diffe rence between corresponding inputs of all four amplifiers. 3 cmrr match is the difference of v os / v cm between any two amplifiers, expressed in db. 4 psrr match is the difference between v os / v supply for any two amplifiers, expressed in db. 5 see figure 5 for test circuit.
ad704 rev. e | page 5 of 16 absolute maximum rat ings table 3. parameter rating supply voltage ? 18 v internal power dissipation (25c) 1 input v oltage ? v s differential input voltage 2 ? 0.7 v output short - circuit duration (single input) indefinite storage temperature range ?65c to +125c operating temperature range ad704j 0c to 70c ad704a ? 40c to +85c lead temperature (soldering , 10 s ec) 300c 1 specification is for the device in free air: 14- l ead p lastic p ackage: ja = 150c/w . 16- l ead soic p ackage: ja = 100c/w . 20- t erminal lcc p ackage: ja = 150c/w . 2 the input pins of this amplifier are protected by back - to - back diodes. if the d ifferential voltage exceeds 0.7 volts, exter nal series protection resistors s hould be added to limit the input current to less than 25 ma. stresses above those listed under absolute maximum ratings may cause permanent damage to the device. this is a stres s rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. 1/4 ad704 input signal 1 9k? 1k? 1k? 2.5k ? 0.1f 1f 0.1f 1f ad704 pin 4 ad704 pin 11 +v s ?v s com output notes 1. all four amplifiers are connected as shown. 1 the signal input (such that the amplifier?s output is at maximum amplitude without clipping or slew limiting) is applied to one amplifier at a time. the outputs of the other three amplifiers are then measured for crosstalk. 00818-005 figure 5 . crosstalk test circuit ?80 ?100 ?120 ?140 ?160 10 100 1k 10k 100k frequency (hz) crosstalk (db) amp2 amp3 amp4 00818-006 figure 6 . crosstalk vs. frequency esd caution
ad704 rev. e | page 6 of 16 typical performance characteristics t a = 25 c, v s = 1 5 v dc, unless otherwise noted. 50 40 30 20 10 0 ?80 ?40 0 40 80 input offset voltage (v) units (%) 00818-007 figure 7 . typical distribution of input offset voltage 50 40 30 20 10 0 ?160 ?80 0 80 160 input bias current (pa) units (%) 00818-008 figure 8 . typical distribution of input bias current 50 40 30 20 10 0 ?120 ?60 0 60 120 input offset current (pa) units (%) 00818-009 figure 9 . typical distribution of input offset current +v s ?0.5 ?1.0 ?1.5 +1.5 +1.0 +0.5 ?v s 0 5 10 15 20 supply voltage (v) input common-mode voltage limit ?v (referred to supply voltages) 00818-010 figure 10 . input common - mode voltage range vs. supply voltage 35 30 25 20 15 10 5 0 1k 10k 100k 1m frequency (hz) output voltage (v p-p) 00818-011 figure 11 . large signal frequency response 100 10 1 0.1 1k 10k 100k 1m 10m 100m source resistance ( ?) output voltage drift (v/c) source resistance may be either balanced or unbalanced. 00818-012 figure 12 . offset voltage drift vs. source resistance
ad704 rev. e | page 7 of 16 50 40 30 20 10 0 ?0.8 ?0.4 0 0.4 0.8 input offset voltage drift (v/c) units (%) 00818-013 figure 13 . typical distribution of input offset voltage drift 4 3 2 1 0 0 1 2 3 4 5 warm-up time (minutes) change in offset voltage (v) 00818-014 figure 14 . change i n input offset voltage vs. warm - u p time 120 100 80 60 40 20 0 ?15 ?10 ?5 0 5 10 15 common-mode voltage (v) input bias current (pa) positive i b negative i b 00818-015 figure 15 . input bias current vs. common - mode voltage 1k 100 10 1 1 10 100 1k frequency (hz) voltage noise (nv/ hz) 00818-016 figure 16 . input noise voltage spectral density 1k 100 10 1 1 10 100 1k frequency (hz) current noise (fa/ hz) 100? 20m ? 10k? v out 00818-017 figure 17 . input noise current spectral density 0 5 10 time (seconds) 0.5v 00818-018 figure 18 . 0.1 hz to 10 hz noise voltage
ad704 rev. e | page 8 of 16 500 +125c +25c ?55c 450 400 350 200 0 5 10 15 20 supply voltage (v) quiescent current (a) 00818-019 figure 19 . quiescent suppl y current vs. supply voltage (per amplifier) 160 140 120 100 80 60 40 20 0 0.1 1 10 100 1k 10k 100k 1m frequency (hz) cmr (db) v s = 15v 00818-020 figure 20 . common - mode rejection vs. frequency 180 160 140 120 100 80 60 40 20 0.1 1 10 100 1k 10k 100k 1m frequency (hz) psr (db) v s = 15v t a = 25c ?psr +psr 00818-021 figure 21 . power supply rejection vs. frequency 10m 1m 100k 1 10 100 load resistance (k ?) open-loop voltage gain +125c +25c ?55c 00818-022 figure 22 . open - loop gain vs. load resistance over temperature 120 100 80 60 40 20 0 140 0 30 60 90 120 150 180 ?20 0.01 0.1 1 10 100 1k 10k 100k 1m 10m frequency (hz) open-loop voltage gain (db) phase shift (degrees) gain phase 00818-023 figure 23 . open - loop gain and phase vs. frequency +v s r l = 10k ? ?0.5 ?1.0 ?1.5 +1.5 +1.0 +0.5 ?v s 0 5 10 15 20 supply voltage (v) output voltage swing ?v (referred to supply voltages) 00818-024 figure 24 . output voltage swing vs. supply voltage
ad704 rev. e | page 9 of 16 1k 100 10 1 0.1 0.01 0.001 1 10 100 1k 10k 100k frequency (hz) closed-loop output impedance ( ?) a v = ?1000 a v = +1 i out = 1ma 00818-025 figure 25 . closed - loop output impe dance vs. frequency 1/4 ad704 +v s 0.1f 0.1f r l 2k? c l r f v out v in ?v s square wave input 00818-026 figure 26 . unity gain follower ( f or large signal applications, resistor r f limits the current t hrough the input protection diodes) 00818-027 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 100 90 10 0% 2v 50s figure 27 . unity gain follower large signal pul se response r f = 10 k , c l = 1 000 pf 00818-028 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 100 90 10 0% 20mv 5s figure 28 . unity gain follower small signal pulse response r f = 0 , c l = 100 pf 00818-029 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 100 90 10 0% 20mv 5s figure 29 . unity gain follower small signal pulse response r f = 0 , c l = 1 00 0 pf 1/4 ad704 +v s 0.1f 0.1f r l 2.5k ? c l 10k? 10k? v out v in ?v s square wave input 00818-030 figure 30 . unity gain inverter connection
ad704 rev. e | page 10 of 16 00818-031 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 100 90 10 0% 2v 50s figure 31 . unity gain inverter large signal pulse response, c l = 1 000 pf 00818-032 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 100 90 10 0% 20mv 5s figure 32 . unity gain inverter small signal pulse response, c l = 100 pf 00818-033 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 100 90 10 0% 20mv 5s figure 33 . unity gain inverter small signal pulse response, c l = 1 000 pf
ad704 rev. e | page 11 of 16 theory of operation ?v in +v in output +v s 0.1f ?v s 0.1f c t c2 c1 r3 6.34k ? r g gain trim (500k ? pot) r4 47.5k ? r5 2.4k ? r1 6.34k ? r2 49.9k ? r6 1m ? r10, 2m ? c5, 0.01f r7 1m ? r8 1m ? 1/4 ad704 1/4 ad704 1/4 ad704 c4 c3 r11, 2m ? c6, 0.01f r9 1m ? 1/4 ad704 dc cmrr trim (5k ? pot) optional ac cmrr trim optional balance resistor networks can be replaced with a short. notes 1. instrumentation amplifier gain = 1 + + (for r1 = r3, r2 = r4 + r5). 2. capacitors c2 and c4 are southern electronics mpcc, polycarbonate, 5%, 50v. 3. all resistors metal film, 1%. r2 r1 2r2 r g q 1 = c1 4c2 = 1 r6 c1c2 r6 = r7 q 2 = c3 4c4 = 1 r8 c3c4 r8 = r9 00818-034 figure 34 . gain - of - 10 instrumentation amplifier with post filtering the instru mentation amplifier with post filtering ( see figure 34 ) combines two applications that benefit greatly from the ad704. this circuit achieves low power and dc precision over temperature with a minimum of components. the instrumentation amplifier circuit offers many performance benefits , including bifet level input bias currents, low input offset voltage drift , and only 1.2 ma quiescent current. it operate s for gains that are g 2 and , at lower gains , it benefit s from no output amplifier offset and no noise con tribution as encountered in a 3 - op - amp design. good low frequency cmrr is achieved even without the optional ac cmrr trim ( see f igure 35 ). table 4 provides resistance values for three common circuit gains. for other gains, use the following equations: 5 10 5 ) ( 2 1 06 . 0 k 8 . 99 1 9 . 0 k 9 . 49 k 9 . 49 ? = ? ? = = ? = + = r3 c g r of value max g r3 r1 r5 r4 r2 t g table 4. resistance values for various gai ns circuit gain (g) r1 and r3 r g (max value of trim potentiometer) bandwidth ( ? 3 db), hz 10 6.34 k ? 166 k ? 50 k 100 526 ? 16.6 k ? 5k 1000 56.2 ? 1.66 k ? 0.5 k 160 140 120 100 80 60 40 20 0 1 10 100 1k 10k frequency (hz) common-mode rejection (db) gain = 10, 0.2v p-p common-mode input typical monolithic in amp without capacitor c t circuit trimmed using capacitor c t 00818-035 figure 35 . common - mode re jection vs. frequency with and w ithout capacitor c t
ad704 rev. e | page 12 of 16 the 1 hz, four - pole active filter offers dc precision with a minimum of components and cost. the low current noise, i os , and i b allow the use of 1 m resistors without sacrificing the 1 v/c drift of the ad704. this means that lower capacitor values can be used, reducing cost and space. furthermore, becaus e the ad704s i b is as low as its i os , over most of the mil temperature range, most applications do not require the use of the normal balancing resistor (with its stability capacitor). adding the optional balancing resistor enhances performance at high tem peratures, as shown in figure 36. tabl e 5 gives capacitor values for several common low pass responses . 180 120 60 0 ?60 ?120 ?180 ?40 0 40 80 120 temperature (c) offset voltage of filter circuit (rti) (v) without optional balance resistor, r3 with optional balance resistor, r3 00818-036 figure 36 . v os vs. temperature performance of the 1 hz filter circuit table 5. 1 hz, four - pole low - pass filter recommended component values 1 desired low pass response section 1 frequency (hz) q section 2 frequency (hz) q c1 ( f) c2 ( f) c3 ( f) c4 ( f) bessel 1.43 0.522 1.60 0.806 0.116 0.107 0.160 0.0616 butterworth 1.00 0.541 1.00 1.31 0.172 0.147 0.416 0.0609 0.1 db chebychev 0.648 0.619 0.948 2.18 0.304 0.198 0.733 0.0385 0.2 db chebychev 0.603 0.646 0.941 2.44 0.341 0.204 0.823 0.0347 0.5 db cheby chev 0.540 0.705 0.932 2.94 0.416 0.209 1.00 0.0290 1.0 db chebychev 0.492 0.785 0.925 3.56 0.508 0.206 1.23 0.0242 1 specified valu es are for a ? 3 db point of 1.0 hz. for other frequencies, simply scale the c1 through c4 capacitors directly; that is , for a 3 hz bessel response, c1 = 0.0387 f, c2 = 0.0357 f, c3 = 0.0533 f, and c4 = 0.0205 f.
ad704 rev. e | page 13 of 16 outline dimensions compliant t o jedec s t andards ms-001 controlling dimensions are in inches; millimeter dimensions (in p arentheses) are rounded-off inch equi v alents for reference on l y and are not appropri a te for use in design. corner leads m a y be configured as whole or half leads. 070606- a 0.022 (0.56) 0.018 (0.46) 0.014 (0.36) 0.150 (3.81) 0.130 (3.30) 0. 1 10 (2.79) 0.070 (1.78) 0.050 (1.27) 0.045 (1.14) 14 1 7 8 0.100 (2.54) bsc 0.775 (19.69) 0.750 (19.05) 0.735 (18.67) 0.060 (1.52) max 0.430 (10.92) max 0.014 (0.36) 0.010 (0.25) 0.008 (0.20) 0.325 (8.26) 0.310 (7.87) 0.300 (7.62) 0.015 (0.38) gauge plane 0.210 (5.33) max sea ting plane 0.015 (0.38) min 0.005 (0.13) min 0.280 (7. 1 1) 0.250 (6.35) 0.240 (6.10) 0.195 (4.95) 0.130 (3.30) 0. 1 15 (2.92) figure 37 . 14 - lead plastic dual in - line package [pdip] narrow body (n - 14) dimensions shown in inches and (millimeters) controlling dimensions are in millimeters; inch dimensions (in p arentheses) are rounded-off millimeter equi v alents for reference on l y and are not appropri a te for use in design. compliant t o jedec s t andards ms-013- aa 032707-b 10.50 (0.4134) 10.10 (0.3976) 0.30 (0.0 1 18) 0.10 (0.0039) 2.65 (0.1043) 2.35 (0.0925) 10.65 (0.4193) 10.00 (0.3937) 7.60 (0.2992) 7.40 (0.2913) 0.75 (0.0295) 0.25 (0.0098) 45 1.27 (0.0500) 0.40 (0.0157) coplanarit y 0.10 0.33 (0.0130) 0.20 (0.0079) 0.51 (0.0201) 0.31 (0.0122) sea ting plane 8 0 16 9 8 1 1.27 (0.0500) bsc figure 38 . 16 - lead standard small outline package [soic_w] wide body (rw - 16) dimensions shown in millimeters and (inches)
ad704 rev. e | page 14 of 16 controlling dimensions are in inches; millimeter dimensions (in p arentheses) are rounded-off inch equi v alents for reference on l y and are not appropri a te for use in design. 1 20 4 9 8 13 19 14 3 18 bot t om view 0.028 (0.71) 0.022 (0.56) 45 ty p 0.015 (0.38) min 0.055 (1.40) 0.045 (1.14) 0.050 (1.27) bsc 0.075 (1.91) ref 0.0 1 1 (0.28) 0.007 (0.18) r ty p 0.095 (2.41) 0.075 (1.90) 0.100 (2.54) ref 0.200 (5.08) ref 0.150 (3.81) bsc 0.075 (1.91) ref 0.358 (9.09) 0.342 (8.69) sq 0.358 (9.09) max sq 0.100 (2.54) 0.064 (1.63) 0.088 (2.24) 0.054 (1.37) 022106- a figure 39 . 2 0 - terminal cerami c leadless chip carrier [lcc] (e - 20- 1) dimensions shown in inches and (millimeters) ordering guide model 1 temperature range package description package option ad704ar -16 ? 40c to +85c 16- lead soic_ w r w -16 ad704ar -16- reel ? 40c to +85c 16- lead soic_ w r w -16 ad704ar z -16 ? 40c to +85c 16- lead soic_ w r w -16 ad704arz -16- reel ? 40c to +85c 16- lead soic_ w r w -16 ad704jn 0c to 70c 14- lead pdip n -14 ad704jn z 0c to 70c 14- lead pdip n -14 ad704jr -16 0c to 70c 16- lead soic_ w r w -16 ad704jr -16- reel 0c to 70c 16- lead soic_ w r w -16 ad704jr z -16 0c to 70c 16- lead soic_ w r w -16 ad704jr z -16- reel 0c to 70c 16- lead soic_ w r w -16 ad704se/883b ? 55c to +125c 20- terminal lcc e -20-1 1 z = rohs compliant part.
ad704 rev. e | page 15 of 16 notes
ad704 rev. e | page 16 of 16 notes ? 2001 - 2010 analog devices, inc. all rights reserved. trademarks and registered trademarks are the property of their respective owners. d00818 - 0 - 1/10(e)

▲Up To Search▲

Price & Availability of AD704JNZ

	To Download AD704JNZ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .